WEEK 16 (FYP 2)

Activity:	Adjust and finalize the fyp thesis .
Objective:	Complete the fyp thesis. Make sure that all the information of this project was included in the thesis. Make sure that there are no mistake and all the information was correct and also was arranged nicely. Make sure that the Plagiarism Result below 20%.
Result :	Figure 1: Softcopy FYP Thesis front page. Figure 2: Plagiarism Result
Conclusion:	I have successfully complete the fyp thesis.

WEEK 15 (FYP 2)

Activity:

FYP 2 INDUSTRY DAY OF STUDENT SEMESTER JULY 2017

                                 o   Date      : 15^th November 2017(Wednesday)

                                 o   Time      : 9.00am – 12.00pm

                                 o   Venue    : UNIKL BMI Gemilang Hall

Figure 1 : Prove Picture

WEEK 14 (FYP 2)

Activity:	Do the poster for Industry Day presentation .
Objective:	Design a poster about this project. Make sure that all the information of this project was display included and correct. Include just needed information and make sure that the information is not so pack.
Result :	Figure 1: Poster.
Conclusion:	I have successfully designed a poster that gives full information about this project.

WEEK 13 (FYP 2)

FYP 2 BRIEFING OF STUDENT SEMESTER JULY 2017

Attend for first briefing Final Year Project 2 for degree student.

                            o   Date      : 3^th November 2017(Wednesday)

                            o   Time      : 3.00pm – 5.00pm

                            o   Venue    : TTL1

·         

The attendances is compulsory 

In the briefing, the FYP committees have briefed us about:

         Final Briefing, 
     

WEEK 12 (FYP 2)

Activity:	Start the assemble the Stepper Motor circuit on the strip board .
Objective:	Construct the circuit on the strip board. Make sure all the connection was correct. Make sure that the Stepper Motor can run and operate same as when simulation was conducted.
Result :	Figure 1: Stepper Motor circuit construction.                                           Figure 2 : Circuit soldering.
Conclusion:	I have successfully construct and solder the circuit on strip board and run also operate the Stepper Motor  same as when it was simulated on breadboard.

WEEK 11 (FYP 2)

FYP 2 BRIEFING OF STUDENT SEMESTER JULY 2017

Attend for first briefing Final Year Project 2 for degree student.

                                                 o   Date      : 20^th October 2017(Friday)

                                                 o   Time      : 3.00pm – 5.00pm

                                                 o   Venue    : TTL1

·         

The attendances is compulsory 

In the briefing, the FYP committees have briefed us about:

         Abstract Writing, 
     Poster,

WEEK 10 (FYP 2)

Activity:	Start the assemble the LCD circuit on the strip board .
Objective:	Construct the circuit on the strip board. Make sure all the connection was correct. Make sure that the LCD can display word same as when simulation was conducted.
Result :	Figure 1: LCD circuit construction. Figure 2 : LCD circuit construction. Figure 3 : LCD Display.
Conclusion:	I have successfully construct and solder the circuit on strip board and display the LCD same as when it was simulated on breadboard.

WEEK 9 (FYP 2)

Activity:

FYP 2 BRIEFING OF STUDENT SEMESTER JULY 2017

Attend for first briefing Final Year Project 2 for degree student.

                                                 o   Date      : 4^th October 2017(Wednesday)

                                                 o   Time      : 3.00pm – 5.00pm

                                                 o   Venue    : TTL1

·         

The attendances is compulsory 

In the briefing, the FYP committees have briefed us about:

         Workshop on Result and Discussion (Chapter 4), 
     Conclusion (Chapter 5),
   

WEEK 8 (FYP 2)

Activity:	Start assemble LCD and  Stepper Motor (23HD5625-P4) together by using Arduino UNO.
Objective:	Find the suitable coding that can match with the components. Study the function and how to assembly the LCD and Stepper Motor (23HD5625-P4) together to the Arduino UNO. Compile and run the LCD and Stepper Motor (23HD5625-P4) together as wanted.
Result :	Figure 1: LCD and  Stepper Motor (23HD5625-P4) simulation
Conclusion:	I have successfully compile and run the LCD and Stepper Motor (23HD5625-P4) togethe as wanted.

WEEK 7 (FYP 2)

Activity:	Meet the Supervisor and discuss about further progress. Ask the Supervisor's opinion certain components.
Objective:	Discuss about further progress with the Supervisor. Ask the Supervisor's opinion. Analyze and study the information given by the Supervisor.
Result :	There several components that been asked by the Supervisor :          - Bubble Detector. Figure 7 : Bubble Detector (Source :http://my.element14.com/optek-technology/opb350/sensor-fluid-0-125-tubing/dp/1497897) Description and explanation:                                      - Model : OPB350                                      - Liquid Sensor                                      - Diameter : 1/8-inch outside  clear tub                                                       - Provides a full solution with automatic                                                        calibration capability and a pre-set trip level.          - Micro Acrylic Beads/Powder.    Figure 8 : Micro Acrylic Beads/Powder (Source :https://www.amazon.com/Moyou-Nail-Art-Massive-different/dp/B006P08IBM) Description and explanation:                                      - Size : Micro                                      - Colour : Mix                                      - Represents waste contain in blood that will be                                            filtered by the kidney (dialyzer).
Conclusion:	Find the component that have been requested by the Supervisor and start assembly it.

WEEK 6 (FYP 2)

Activity:

FYP 2 BRIEFING OF STUDENT SEMESTER JULY 2017

Attend for first briefing Final Year Project 2 for degree student.

The briefing was conducted by Dr .Siti Marwangi Mohamad Maharum.

                                                 o   Date      : 6^th September 2017(Wednesday)

                                                 o   Time      : 3.00pm – 5.00pm

                                                 o   Venue    : TTL1

·         

The attendances is compulsory 

In the briefing, the FYP committees have briefed us about:

         Workshop on Introduction (Chapter 1), 
     Literature Review (Chapter 2),
     Methadology (Chapter 3), 

·  

WEEK 5 (FYP 2)

Activity:	Start assemble Stepper Motor (23HD5625-P4) by using Arduino UNO.
Objective:	Find the suitable coding that can match with the components. Study the function and how to assembly the Stepper Motor (23HD5625-P4) to the Arduino UNO. Compile and run the Stepper Motor (23HD5625-P4) as wanted.
Result :	Figure 1: Stepper Motor (23HD5625-P4) simulation
Conclusion:	I have successfully compile and run the Stepper Motor (23HD5625-P4) as wanted.

WEEK 4 (FYP 2)

Activity:	Start assemble LCD by using Arduino UNO.
Objective:	Find the suitable coding that can match with the components. Study the function and how to assembly the LCD to the Arduino UNO. Compile and display the LCD as wanted.
Result :	Figure 1: LCD Display simulation
Conclusion:	I have successfully compile and display the LCD as wanted.

WEEK 3 (FYP 2)

Activity:

FYP 2 BRIEFING OF STUDENT SEMESTER JULY 2017

Attend for first briefing Final Year Project 2 for degree student.

The briefing was conducted by Dr .Siti Marwangi Mohamad Maharum.

                                                 o   Date      : 18^th August 2017(Friday)

                                                 o   Time      : 3.00pm – 5.00pm

                                                 o   Venue    : TTL1

·         

The attendances is compulsory 

In the briefing, the FYP committees have briefed us about:

         Objectives, 

·        FYP Assessment Scheme,
     FYP Scope,
·        Project Titles Guideline, 
     FYP Claim,
     Plagiarism,
     Progress Report,
     FYP Thesis Components,
     FYP Final Report,
     FYP Activities,

WEEK 2 (FYP 2)

Activity:	Continue analyze several components that will be used for the project.
Objective:	Analyze several components used. Study the data sheet and manual of the components. Find the function and the specification of using the components.
Result :	LCD (liquid crystal display) 20X4 Figure 4 : LCD (liquid crystal display) 20X4  (Source :http://www.continentalee.com.sg/lcd-20x4 ) Water Filter Figure 5 :Water Filter  (Source :http://www.lazada.co.th/water-filter-housing-diy-fill-t33-shell-filter-254cm-bottle-14tube-fittings-transparent-thicken-for-reverse-osmosis-system-9450290.html)          Water filter used to replace dialyzer beacuse its has same function. Jumper Cable Figure 6 : Jumper Cable  (Source :https://www.amazon.in/Robo-India-JW-C3-Jumper-Wire/dp/B00YJ67SYW )                                     There are 3 types of jumper used:                                            1) Female to female                                            2) Male to male                                            3) Male to female
Conclusion:	I have successfully analyze several components used.

WEEK 1 (FYP 2)

Activity:	Meet the Supervisor and discuss about further pro Start analyze several components that will be used for the project.
Objective:	Analyze several components used. Study the data sheet and manual of the components. Find the function and the specification of using the components.
Result :	Arduino UNO Figure 1 : Arduino UNO (Source :https://eeeproject.com/arduino-uno-board/ ) TB6560 single Axi Stepper Motor Driver Figure 2 : TB6560 single Axi Stepper Motor Driver (Source :http://www.stepmotordriver.com/TB6560-single-Axi-Stepper-Motor-Driver-DC7-32V-3A-CNC-stepper-motor-controller-16.html ) DC Water Pump Figure 3 : DC Water Pump  (Source :http://www.dx.com/p/szf280-6-9v-mini-water-pump-motor-silver-white-205019#.WcsYl7IjHIU )
Conclusion:	I have successfully analyze several components used.